Your furnace or heat pump is 12-15 years old and repairs are getting frequent
Heat Pumps · Kent, WA
Heat Pump Installation in Kent, WA
Most heat pump installations in Kent run $6,500-$15,500 installed, depending on system size and ductwork condition. SPS Pro Services installs heat pumps throughout Kent and the Kent Valley, with most jobs scheduled within a week and completed in one to two days.
Typical cost$6,500–$15,500
WarrantyWorkmanship warranty
AvailabilitySame-week visits
HoursMon–Fri 8am–6pm
On service calls across Kent we see the same failure patterns repeat: heat pumps sized for the home's original 1970s furnace rather than today's insulation and window upgrades, outdoor units set directly on grade in low-lying Kent Valley spots that flood or trap moisture, and defrost control boards that fail after a few winters because the unit was never rated for our marine cold snaps. We size and place every system to avoid these specific problems.
Local knowledge
What's different about heat pump installation in Kent
Every area we serve is different — in Kent, these three factors matter most.
Kent Valley homes built before 1990 often carry 100-amp electrical panels that can't support a heat pump's outdoor unit plus a backup coil without an upgrade, which we check before quoting.
PSE serves electric in Kent, and off-peak heat pump operation can lower winter bills compared to the electric baseboard heat still common in East Hill and Panther Lake ramblers.
Low-lying areas near the Green River and West Hill see more standing water and freeze-thaw cycling, so we set outdoor condensers on elevated pads rated for our wet winters.
Symptoms we see daily
Signs you need heat pump installation in Kent
You have no central air and summers in your home are uncomfortable
You're heating with electric baseboards and utility bills spike every winter
Rooms heat or cool unevenly no matter how you adjust the thermostat
You're planning a remodel or addition and need new HVAC capacity
No surprises
How a Kent heat pump installation visit works
1
Home and load assessment
We inspect existing ductwork, electrical panel capacity, and insulation levels specific to your Kent home's age and construction before recommending a system size.
2
System design and quote
You get a written estimate within the $6,500-$15,500 range based on equipment tier, indoor coil compatibility, and any electrical upgrades needed.
3
Permitting
We pull the required King County or City of Kent mechanical and electrical permits and schedule inspections so the install stays code compliant.
4
Installation
Most installs take one to two days, including setting the outdoor unit on a proper elevated pad, running refrigerant lines, and connecting to existing or new ductwork.
5
Startup and walkthrough
We charge the system to manufacturer spec, test the defrost cycle, and walk you through the thermostat before we leave.
Flat-rate pricing
Heat Pump Installation in Kent — what it costs
Conservative ranges for the Seattle metro. Your written quote is exact before work begins.
| Job | Typical price |
|---|---|
| In-home estimateExact flat quote for your home | Free |
| Standard heat pump installationTypical single-system job | $6,500–$9,500 |
| Mid-range heat pump installationHigher-capacity or multi-zone equipment | $9,500–$12,500 |
| Complex heat pump installationPremium equipment or difficult access | $12,500–$15,500 |
Prices reviewed by Sergei Petrov · July 2026. Parts availability can shift ranges — the quote you sign is final.
24/7 Emergency Line
Emergency dispatchNo heat at 11pm? We pick up.
Office hours are Mon–Fri, but the emergency line never closes. Call any hour and we dispatch a licensed tech across Greater Seattle.
Straight answers
Heat Pump Installation in Kent — FAQ
Why do heat pumps in Kent fail sooner than expected?
The most common issue we find on Kent service calls is a system sized for the original home rather than current insulation and window upgrades, which causes short cycling and early compressor wear. Improper outdoor unit placement in low-lying yards that collect water is the second most frequent cause of early failure.
Will my Kent home need an electrical panel upgrade?
Many homes in Kent Valley and East Hill built before 1990 have 100-amp panels that are near capacity once you add a heat pump and backup heat strip. We check your panel load during the assessment and include any upgrade cost in your quote before work starts.
How long does installation take once I schedule?
We typically book Kent installs within a week of your call, and the physical install takes one to two days depending on whether existing ductwork needs modification. Permit inspection scheduling with King County can add a few days to the overall timeline.
Do you service Kent neighborhoods outside the valley floor?
Yes, we install throughout Kent including East Hill, West Hill, and the valley itself, as well as nearby Seattle, Bellevue, Redmond, Kirkland, and Sammamish. Placement and sizing recommendations differ by elevation and exposure, which we account for on-site.
Founder & Lead HVAC Technician, SPS Pro Services
EPA Section 608 UniversalNATE Core Certified14+ years in the trade
Reviews the pricing and service guidance on this page against SPS Pro Services's actual job records in Kent and across the Seattle metro.
Prices reviewed July 2026
Also in Kent
Other services our crew handles on the same routes.
Need heat pump installation in Kent?
Call (206) 427-8907 to schedule a Kent heat pump assessment and get a firm quote before we start any work.