Your furnace or heat pump is 12-15 years old and repairs are getting frequent
Heat Pumps · Edmonds, WA
Heat Pump Installation in Edmonds, WA
Heat pump installation in Edmonds typically runs $6,500 to $15,500 installed, depending on system size, ductwork, and electrical needs. SPS Pro Services has installed heat pumps across Snohomish County since 2017, and most Edmonds projects are scheduled within a week, with the physical install finished in one to two days.
Typical cost$6,500–$15,500
WarrantyWorkmanship warranty
AvailabilitySame-week visits
HoursMon–Fri 8am–6pm
Every heat pump install in Edmonds needs a mechanical permit and an electrical permit through the City of Edmonds, with the wiring inspected under Washington State L&I code. We pull both permits before any equipment shows up, coordinate the L&I inspection, and hand you signed-off paperwork when we're done — not just a running system, but one that will clear resale inspection and insurance review later.
Local knowledge
What's different about heat pump installation in Edmonds
Local housing stock and utilities in Edmonds change what this work involves.
Many Edmonds homes date to the 1950s–1970s with 100-amp electrical panels; a heat pump often needs a dedicated 220-volt circuit, so we check panel capacity before quoting and flag upgrades early rather than mid-job.
Edmonds' marine climate keeps winter lows mild compared to inland Snohomish County, so a properly sized heat pump can usually cover heating without backup strip heat, cutting the equipment cost some other cities require.
Bluff and slope lots near the waterfront in Edmonds can trigger setback and drainage rules for outdoor condenser placement; we confirm siting against city code before the mechanical permit is filed, not after the unit is set.
Symptoms we see daily
Signs you need heat pump installation in Edmonds
You have no central air and summers in your home are uncomfortable
You're heating with electric baseboards and utility bills spike every winter
Rooms heat or cool unevenly no matter how you adjust the thermostat
You're planning a remodel or addition and need new HVAC capacity
No surprises
How a Edmonds heat pump installation visit works
1
Home Assessment & Permit Filing
We measure your home's heating load, inspect existing ductwork or line-set routing, and file the mechanical and electrical permits with the City of Edmonds before scheduling install day.
2
Electrical Panel Check
We verify your panel has capacity for a new 220-volt circuit; if it doesn't, we quote the upgrade upfront so there are no surprise costs once work begins.
3
Equipment Selection & Line Set Installation
We size the outdoor and indoor units to your square footage and insulation, then run refrigerant lines and condensate drainage per L&I code and manufacturer specs.
4
Mechanical Install & L&I Inspection Scheduling
Our crew sets the outdoor unit, connects indoor air handlers or ducted coils, wires the system, and books the required L&I electrical inspection before startup.
5
Final Walkthrough & Permit Sign-off
We test heating and cooling modes, walk you through the thermostat, and provide copies of the closed permits and inspection sign-off for your records.
Flat-rate pricing
Heat Pump Installation in Edmonds — what it costs
Conservative ranges for the Seattle metro. Your written quote is exact before work begins.
| Job | Typical price |
|---|---|
| In-home estimateExact flat quote for your home | Free |
| Standard heat pump installationTypical single-system job | $6,500–$9,500 |
| Mid-range heat pump installationHigher-capacity or multi-zone equipment | $9,500–$12,500 |
| Complex heat pump installationPremium equipment or difficult access | $12,500–$15,500 |
Prices reviewed by Sergei Petrov · July 2026. Parts availability can shift ranges — the quote you sign is final.
24/7 Emergency Line
Emergency dispatchNo heat at 11pm? We pick up.
Office hours are Mon–Fri, but the emergency line never closes. Call any hour and we dispatch a licensed tech across Greater Seattle.
Straight answers
Heat Pump Installation in Edmonds — FAQ
Do I need a permit for heat pump installation in Edmonds?
Yes. The City of Edmonds requires a mechanical permit for the heat pump itself and an electrical permit for the circuit, both inspected under Washington State L&I code. We handle filing and scheduling both, and you get copies of the closed permits when the job is done.
My Edmonds home has an older electrical panel — does that add cost?
It can. Many Edmonds houses built before 1980 have 100-amp panels that are already near capacity. If a panel upgrade is needed for the heat pump's dedicated circuit, we quote it separately upfront so it's not a surprise after the L&I inspection is scheduled.
Will a heat pump keep up during a Puget Sound cold snap in Edmonds?
For most Edmonds homes, yes — winter lows rarely stay below freezing for long near the water. We size the system with your home's insulation and square footage in mind, and for homes with older single-pane windows we may recommend a slightly larger unit or backup heat strip.
Can I put the outdoor unit anywhere in my Edmonds yard?
Not always. Homes on bluff or slope lots near the waterfront can have setback and drainage restrictions tied to Edmonds' critical areas code. We check placement against city rules before filing the permit so the unit doesn't need to be relocated after installation.
Founder & Lead HVAC Technician, SPS Pro Services
EPA Section 608 UniversalNATE Core Certified14+ years in the trade
Reviews the pricing and service guidance on this page against SPS Pro Services's actual job records in Edmonds and across the Seattle metro.
Prices reviewed July 2026
Also in Edmonds
Other services our crew handles on the same routes.
Need heat pump installation in Edmonds?
Call (206) 427-8907 to schedule a heat pump assessment in Edmonds — we handle the permits and L&I inspection so you don't have to.