Furnace is 15 years or older and repair calls are becoming frequent
Heating · Everett, WA
Furnace Replacement in Everett, WA
Most Everett furnace replacements run $4,800 to $9,800 installed, depending on furnace size and ductwork condition. SPS Pro Services installs gas and electric furnaces throughout Everett and Snohomish County, with most single-day jobs completed start to finish and the old unit hauled away same visit.
Typical cost$4,800–$9,800
WarrantyWorkmanship warranty
AvailabilitySame-week visits
HoursMon–Fri 8am–6pm
Everett's housing stock spans a wide range, from early 1900s Craftsman homes in the Riverside and Bayside neighborhoods to the wave of ranch and split-level houses built during the 1940s-1960s Boeing employment boom, plus newer construction farther east. Older homes often still run on the original duct layout sized for a smaller furnace, so a straight swap without checking duct capacity can leave rooms unevenly heated. We size the new unit to your actual house, not just the one being replaced.
Local knowledge
What's different about furnace replacement in Everett
Everett homes have their own quirks, and after years of visits here we know them well.
Many Everett homes near Silver Lake and north Everett were built between 1945 and 1965, when furnaces were commonly oversized for the ductwork installed at the time; we check static pressure before recommending a replacement size.
Everett winters bring damp, low-40s air off Puget Sound for weeks at a time, so a furnace that short-cycles or struggles to reach set temperature burns more gas and wears out faster.
PSE supplies natural gas to most Everett neighborhoods while Snohomish County PUD handles electric service, which affects whether a gas furnace, electric furnace, or hybrid heat pump setup makes more financial sense for a given address.
Symptoms we see daily
Signs you need furnace replacement in Everett
Uneven heating between rooms or a thermostat that won't hold temperature
Energy bills climbing with no change in how the home is used
Pilot light burns yellow instead of blue, or you notice odd smells when it runs
Banging, rattling, or grinding noises when the furnace starts up
No surprises
How a Everett furnace replacement visit works
1
In-home assessment
We inspect your current furnace, measure duct static pressure, and check venting and gas line sizing before quoting anything, especially important in older Everett homes with original ductwork.
2
Written estimate
You get a clear price within the $4,800-$9,800 range based on furnace size, efficiency rating, and any duct or venting corrections needed, no surprise add-ons after work starts.
3
Removal and prep
We disconnect and remove the old furnace, protect flooring and entry paths, and confirm gas, electrical, and venting connections match code before the new unit goes in.
4
Installation
The new furnace is set, connected to existing or upgraded ductwork, and tested for airflow and gas pressure, most installs completed in one working day.
5
Startup and walkthrough
We run a full heat cycle, check thermostat operation, and walk you through filter location and maintenance before we leave, plus haul away the old unit and packaging.
Flat-rate pricing
Furnace Replacement in Everett — what it costs
Conservative ranges for the Seattle metro. Your written quote is exact before work begins.
| Job | Typical price |
|---|---|
| In-home estimateExact flat quote for your home | Free |
| Standard furnace replacementTypical single-system job | $4,800–$6,470 |
| Mid-range furnace replacementHigher-capacity or multi-zone equipment | $6,470–$8,130 |
| Complex furnace replacementPremium equipment or difficult access | $8,130–$9,800 |
Prices reviewed by Sergei Petrov · July 2026. Parts availability can shift ranges — the quote you sign is final.
24/7 Emergency Line
Emergency dispatchNo heat at 11pm? We pick up.
Office hours are Mon–Fri, but the emergency line never closes. Call any hour and we dispatch a licensed tech across Greater Seattle.
Straight answers
Furnace Replacement in Everett — FAQ
How long does a furnace replacement take in Everett?
Most jobs are completed in a single day, roughly 6 to 8 hours, assuming no major ductwork changes are needed. Older Everett homes with restrictive crawlspace access or knob-and-tube wiring nearby sometimes add a couple hours for careful routing.
Do I need to replace ductwork with a new furnace?
Not always. Many homes built during Everett's 1950s-60s growth period have ductwork sized for a smaller furnace, so we measure static pressure first. If the existing ducts can't move enough air, we'll flag it before install rather than after.
What furnace size is right for my Everett home?
It depends on square footage, insulation age, and duct condition rather than just matching the old unit. A 1920s Craftsman near downtown Everett and a 1960s rancher near Silver Lake often need different sizing even at similar square footage.
Do you serve areas outside Everett proper?
Yes, we cover Everett along with Arlington, Monroe, Lynnwood, Marysville, and Snohomish, all within the same Snohomish County service area and typical response times.
Founder & Lead HVAC Technician, SPS Pro Services
EPA Section 608 UniversalNATE Core Certified14+ years in the trade
Reviews the pricing and service guidance on this page against SPS Pro Services's actual job records in Everett and across the Seattle metro.
Prices reviewed July 2026
Also in Everett
Other services our crew handles on the same routes.
Need furnace replacement in Everett?
Call (206) 427-8907 to schedule a furnace replacement estimate for your Everett home, Monday through Friday 8am to 6pm.